How to choose
November 22, 2024
Electric bicycle lights are more than just accessories. They form part of the integral setup for safety and visibility issues.
They are super important for noticing ongoing traffic and for other people on the streets and roads to notice you.
However, the light and all the controls included can be overwhelming, especially for a new e-bike owner.
Continue reading to learn how to use your e-bike lighting system effectively.
Most e-bikes come with front and rear lighting. The light itself can vary.
When we are speaking about e-bike lights are mostly connected with the main battery of the e-bike.
They are necessary when riding in the night, as these provide visibility both to the rider and others.
NYC bike lighting legal requirements are clear. You must be visible on the road.
Turn on any of your e-bikes by pressing the 'MODE' or power button, depending on your control panel, and hold it down until the display lights up.
That would mean the bike is turned on. This may be different with some models.
As for the front lights, it depends on the model. Holding the 'Plus (+)' button on the control pad works on some, while on others, pressing 'MODE' and 'UP' arrows at the same time does the job.
Also, most bikes have different light modes depending on your needs.
There is usually a button on the light unit for rear lights.
One click turns on, another click goes into a blink mode, while a third click changes to a longer blinking interval.
Most e-bikes will provide the option to switch the light settings: steady to blinking and off. Typically, this could be on the control panel or on the light unit itself.
General troubleshooting for light problems with an electric bike would involve checking the power source.
Most e-bike lights get their power from the main battery or an independent battery pack; hence, ensuring that the battery is charged and correctly attached will be a major vital first step.
Keep in mind that this has the other side to it.
If the lights aren’t working properly, chances are they’ll be draining your battery power at a much faster rate.
If the lights are weak or not working at all, maybe it is because of a dead or low battery, and therefore, recharging it might do the magic.
Look at the wiring and connections next.
The lights are cut off from power if the wires are loose, frayed, or disconnected.
Check the cables carefully for any damages, and make sure all the connections are tight enough.
If the problem persists, then the light switch needs to be tested to verify that it is in good condition since an incompetent switch could be replaced.
Finally, if the lights still don't work, the LEDs themselves may be defective. Replace them with their respective compatible components and check again.
Where the problems of electricity are intricate, it would be better to get advice from a professional or consult the bike manual provided.
If you are using Whizz protection plan, service repairs can be covered by us.
Regular tune-ups will prevent light issues and make your e-bike function as it should.
Related: Can you use an e-bike as a normal bike
Keeping your electric bike lights not only guarantees steady performance of the accessory but also enhances your riding safety.
Cleaning regularly with a soft, moist cloth will keep dirt and debris that diminish brightness off the lights.
Periodically check on the wiring and connections to make sure they are secure and free from corrosion or damage.
Look for any cracks in the light housing or ingress of water, especially after riding in wet conditions, since water can damage the electrical components.
Replace any worn-out bulbs or LEDs in adequate time with compatible ones to keep the light optimally illuminated.
If your lights draw power from a separate battery pack, make sure that batteries are fully charged and stored appropriately when not in use.
In the case that your lights are connected to the main battery, pay attention to your battery health to avoid suddenly shutting off.
Further protection against environmental elements will be given to the light system by keeping your bike parked in a dry, covered area.
Paying regular attention to these details will go a long way in extending the life of your e-bike lights.
Don’t forget that regular e-bike maintenance is the key to keeping your entire bike working properly for as long as possible.
Related: How to choose the best e-bike for food delivery
Well, there you have it. This has been your complete guide to electric bicycle lights.
Properly functioning lights are a prerequisite to enjoying your e-bike experience fully and safely; hence, this should make sure that you have all the important information concerning these items so you can handle them appropriately.
Also, keep in mind that some states require daytime running lights. Just because you’re not driving in the dark doesn’t mean you can neglect this part of your bike.
When you buy an e-bike from a reliable company, such as Whizz, you’re also making sure you’ll end up with a bicycle with high-quality, long-lasting lights.
Invest your money in a quality electric bike, and you’ll lower the monthly costs.
Choose Whizz and ride without care.
